MIL-PRF-2819H
h.
i.
j.
Material safety data sheets, when required (see 6.4).
k.
Carton identification markings (see 6.10).
6.3 Qualification. With respect to products requiring qualification, awards will be made only for products
which are, at the time of award of contract, qualified for inclusion in Qualified Products List 2819 (QPL-2819)
whether or not such products have actually been so listed by that date. The attention of the contractors is called to
these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the
Federal Government tested for qualification in order that they may be eligible to be awarded contracts or orders for
the products covered by this specification. Information pertaining to qualification of products may be obtained from
Commander, Naval Sea Systems Command, ATTN: SEA 05S, 1333 Isaac Hull Avenue, SE, Stop 5160,
Washington Navy Yard DC 20376-5160 or emailed to CommandStandards@navy.mil. An online listing of
products qualified to this specification may be found in the Qualified Products Database (QPD) at
6.4 Material safety data sheets. Contracting officers will identify those activities requiring copies of completed
Material Safety Data Sheets prepared in accordance with FED-STD-313. In order to obtain the MSDS, FAR clause
52.223-3 must be in the contract.
6.5 Commercial sizes. Commercial sizes and thicknesses of block insulation covered by this specification are
industry standards. Other sizes and thicknesses may be obtained upon request.
6.6 Toxicity evaluation. The Navy and Marine Corps Public Health Center (NMCPHC) requires sufficient
information to permit an HHA of the product. Upon completion of the HHA, a copy will be provided by the
NMCPHC to the Government for evaluation.
6.7 Off-gassing. Materials to be installed in submarines are to be controlled to prevent off-gassing, which
contaminates the atmosphere and can result in health hazards to personnel or deleterious effects on machinery.
These controls are accomplished through the Submarine Material Control Program, which is described in the
Nuclear Powered Submarine Atmosphere Control Manual, S9510-AB-ATM-010 chapter titled "Material Control
Program." Under the Submarine Material Control Program, all materials considered for use on submarines require
certification and assignment of a usage category. Under the certification process, candidate materials are selected by
Navy activities or contractors, and a request for certification is submitted to the Naval Sea Systems Command, SEA
05S, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard, DC 20376-5160 or emailed to
CommandStandards@navy.mil. The certification request is accompanied by detailed information, including
descriptions of the material, method of application, usage, and storage. A chemical analysis is conducted, which is
normally accomplished through off gas testing. The off gas test is required to be conducted in a Government
approved laboratory designated by the preparing activity. Information pertaining to this test requirement may be
obtained from the Naval Sea Systems Command, SEA 05S, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington
Navy Yard, DC 20376-5160 or emailed to CommandStandards@navy.mil. Based on the chemical analysis results,
a usage category is assigned to the material defining whether, and to what extent, the material may be used on
submarines.
6.8 Additional fire testing provisions. NAVSEA reserves the right to witness the tests, and/or perform any of
the tests set forth herein where such testing is deemed necessary to assure compliance to prescribed requirements of
the qualification tests.
6.9 Certification. Consideration should be given to including certificates of compliance with each shipment of
insulation. Certificates should indicate successful completion of the individual tests of the conformance inspection.
6.10 Carton identification markings. Unless otherwise specified (see 6.2), each carton should be marked with
the following information:
"Asbestos free."
a.
b.
Specification number and class.
c.
Maximum temperature limit.
8
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business